GoodWe uses the SEMS (Smart Energy Management System) platform for monitoring and control. There are two tiers: SEMS (standard): The standard monitoring app and web portal for homeowners. Available at semsportal.com or via the SEMS app (iOS and Android). SEMS+ (premium): An enhanced version with more detailed analytics, energy cost calculations, and advanced battery control. Some GoodWe hybrid systems (particularly ET and EH series with Lynx batteries) include SEMS+ features. The SEMS portal login you use for the web and app is the same account.
Home Screen and Energy Flow Diagram
When you open the SEMS app:
- The home screen shows your plant (system)
- Tap the plant to open the energy flow view
- The energy flow diagram shows:
- Solar panels (top): current PV generation in kilowatts
- Battery (side): current SOC percentage and charge/discharge rate in kilowatts
- Home/Load (centre): current home consumption in kilowatts
- Grid (bottom): current grid import (in) or export (out) in kilowatts
- Arrows show the direction of energy flow in real time
Reading Your Daily and Historical Data
From the plant screen:
- Tap the chart icon or go to Statistics
- Select Day, Month, or Year
- The daily view shows:
- PV generation (total solar produced in kWh)
- Consumption (total home load in kWh)
- Battery charge (kWh charged into battery)
- Battery discharge (kWh delivered from battery)
- Export to grid (kWh sold to grid)
- Import from grid (kWh purchased from grid)
- Self-consumption rate: the percentage of your solar that was used by the home or battery (not exported)
- Self-sufficiency rate: the percentage of your home's energy needs met by solar and battery (not imported)
Checking Fault Codes and Events
- Open the SEMS app and select your plant
- Tap the inverter icon or go to Device
- Select the inverter or battery device
- Tap Events or Alarm Records
- Active alarms are shown at the top; historical events are listed below
- Each alarm has a code (F01, W02, etc.), a description, and a start time
For details on what each fault code means: see the GoodWe ES/ESH fault codes article (single-phase hybrid), the GoodWe ET three-phase fault codes article, or the GoodWe DNS string inverter fault codes article.
Changing the Working Mode
The working mode determines how the battery operates. Accessible in SEMS app:
- Open your plant
- Tap the inverter icon
- Scroll to Working Mode or go to Settings > Battery Control
- Available modes (note: availability depends on your inverter and battery model):
General Mode (Self-Consumption): Solar charges battery; battery discharges to home when solar is insufficient; grid provides remaining load. This is the recommended mode for most customers.
Backup Mode: Battery is reserved for grid outage backup only. Battery SOC is maintained at the backup reserve level. The home imports from the grid during normal operation. Use this if you want to guarantee a backup reserve and are not concerned about self-consumption.
Feed-in Priority: Solar exports to grid first; any surplus (above export limit) charges the battery; battery then discharges for home load. Not recommended for most customers as it reduces self-consumption.
Peak Shaving (TOU): The system follows a time-of-use schedule. Charge during off-peak, discharge during peak. Set up the TOU schedule in Settings > Battery Control > TOU Settings.
Off-Grid Mode: Only available for systems installed with off-grid configuration. Do not activate this mode on a grid-connected system.
Setting the Backup Reserve SOC
The backup reserve (also called minimum SOC or backup SOC) is the battery level below which the battery will not discharge during normal operation. It is reserved for grid outage use.
- In the SEMS app: go to Settings > Battery Control
- Find Battery Reserve or Min SOC
- The default is typically 20% (battery discharges down to 20% for self-consumption and keeps 20% in reserve)
- Setting this to 100% means the battery never discharges to the home; it sits at 100% all day and you import from the grid. This is a common cause of unexpected grid imports.
- Setting this to 0% means the battery will fully discharge with no reserve. For most customers 10 to 20% is appropriate.
GoodWe Wi-Fi Logger Offline Reconnection
If the SEMS app shows your system offline (no new data in 24+ hours):
- Check your home internet is working
- Check the Wi-Fi logger on the inverter: there is a small Wi-Fi dongle plugged into the inverter's USB-style port. Its LED should be green (connected).
- If the LED is off or flashing: the logger needs to reconnect to your Wi-Fi.
- The GoodWe logger broadcasts a temporary Wi-Fi hotspot named GW-xxxxxxxx when not connected to a home network.
- On your phone: connect to the GW-xxxxxxxx network
- Open a browser and go to 10.10.100.254 (this is the logger's local IP when in AP mode)
- Log in (default credentials: admin / admin or as printed on the logger label)
- Go to Wi-Fi Settings > Connect to Home Network and select your home Wi-Fi
- Enter your Wi-Fi password and save
- The logger will disconnect from the hotspot and reconnect to your home network. Wait 2 to 3 minutes and check SEMS app.
Note: if your Wi-Fi password changed and the logger lost connection as a result: this is the procedure to reconnect.
Transferring SEMS Account to a New Owner
If you have purchased a property with a GoodWe system:
- You will need the inverter serial number (on the inverter label)
- Contact GoodWe Australia: au.goodwe.com > Support, or ask AEU to assist with the transfer
- The previous owner's account must be removed before a new account can be associated
- AEU can assist with account transfers for systems we installed
When to Call AEU
Call AEU on 1300 996 917 if:
- An active fault or alarm is showing in SEMS and you are not sure what it means
- The SEMS app shows zero production on a clear day
- You cannot reconnect the Wi-Fi logger and the local web interface is not accessible
- You want to change the working mode but cannot locate the setting
- You need help interpreting historical SEMS data for a warranty or performance claim


